Skip to main content
27 results for@MasterFX #3d-printers
Advanced filters
Relevance
Relevance
Nov '15
-
1. Leveling After you leveled your printing bed with the internal leveling wizard, start printing a huge square (something like this: http://www.thingi...
Jun '17
-
Connect you printer Via USB. Start ReplicatorG Go to File = > Preferences = > Advanced. Enter " http://jettyfirmware.yolasite.com/resources/release/fir...
Oct '15
-
Never had that problem. But it also could be a slicer problem (bad gcode generation). Try Makerware oder something else to verify that you slicer is no...
Feb '17
-
If your last USB chip burned out, you mabe have an grounding/earthing issue. Is your PC on the same mains line? Or you try it with o notebook on batter...
Sep '16
-
Can you show images? If there is something wrong in the Software it should always print to small. But you said it is not everytime the case. Do you hea...
Aug '16
-
First of all you should check all connection screws of your power supply and mainboard. They must be tight since the vibrations can cause connection is...
Jul '16
-
Blue tape with abs is not the best. ABS you should use capton or glass bed with ~100°C
Jun '16
-
I replaced all bearing with IGUS exept the Z-Axis since it is moving not that much that it would be a big difference. But if you want to, just unscrew...
Mar '16
-
Mmmh, thats truly a little bit strange. Ok a round cylinder is a very continuously, smooth movement on both axis, where the rectangle style objects hav...
Jun '16
-
First of all I would check if the screws on the mainboard are not loose. I have my ctc for 2,5 Years now and over 1000 printing hours and I didn't have...
Jun '16
-
Scale it in your slicer to 101%. The materials are shrinking. ABS is shrinking more than PLA.
Oct '15
-
You need a PTEFE Tube with 3mm Outer diameter and 2mm inner diameter. About 3€ on Ebay/m
Mar '16
-
You can download the complete plans for building the makerbot: http://www.thingiverse.com/thing:18813 The MakerBot Replicator by MakerBot - Thingiverse...
Mar '16
-
Do you have a picture from your preview? What are your support settings? Can you post your factory file?
Mar '16
-
I have a CTC since two years and no problems so far. > 1.Infill not touching in some areas This could be a problem with the slicer, maybe there is some...
Mar '16
-
All Version 2, but Version 3 for top. I suggest you close the holes for the screws on Top 3 with only one layer, than you don't need support
Feb '16
-
You have to use Replicator G to update you CTC. Start Replicator G go to File = > Preferences = > Advanced. Change the Firmware Update URL to " http://...
Feb '16
-
I had no problems to unscrew the nozzle (4 times so far clean it and change the PTFE tube)
Dec '15
-
I print my PETG @ 240-250°C and 50-60mm/s and 100° C Printbead temperature. My extusion multiplyer is 1.10. Everything is fine until now.
Dec '15
-
Especially for small parts you should install a cooling fan for the filament, since the each layer is printed for a very short time, the filament doesn...
Nov '15
-
Since it doesn't have to do with the X-Y Direction would say it is a cooling problem. The Material on the left picture did cool down to slow, where as...
Oct '15
-
If you install the latest Sailfish Firmware (via ReplicatorG, which works well on CTC) you can tune the Speed and Temperature while you're printing. I...
Oct '15
-
It doesn't look too bad. The problem is, that your fan only cools the front of the model, not the direct printed part. A fan on the extrufer (which mov...
Oct '15
-
> 1- is this printer good for a beginner and knowing that printer is my first !! I would say yes. I've no problems with that printer from the beginning...
Oct '15
-
Try to use Makerbot Software at first an see if your problem is gone. This might be some problem of your printer settings. Maybe you selected the wrong...
Aug '15
-
I'm using 230°C for pla @ 65°C bed temp with relativ fast printing speeds (60-70mm/s) and 240-245 °C for abs @ 110°C bed temp
Jun '15
-
Have you enabled the Dual-Extruder Options in the Settings menu?