Skip to main content
24 results for@ebam #3d-printers
Advanced filters
Relevance
Relevance
Jan '17
-
Had some really good prints recently up until a couple of days ago when it appears to start shifting ever so slightly as you can see in the photo. The...
Dec '16
-
Hi all, I'm wanting to replace my hotend rods (the bit you put ptfe tubing in) and I can't find any on aliexpress or ebay that look like them. The nozz...
Aug '16
-
Hi hope you are we posted in aother thread about the settings you need to write down so after you upgrade you can enter them… which settings are these?...
Feb '17
-
The fan for my right extruder (CTC Bizer Dual) had started to run a little slowly so I replaced it. Did all the checks that I had rewired a new one (12...
Feb '17
-
Printer stopped mid print. Was printing using the right extruder and haven't used the left for ages. Printer says my 'heater error, my temperature read...
Jan '17
-
Printed black piece 1st with filament spool on side of the printer, pink/purple was next and was printed with the spool at the side of the printer near...
Dec '16
-
Hi do you have a link for the fan you have put in place to cool the print?
Dec '16
-
Ebay might not enforce a 1 year warranty but if you paid via Paypal or credit card they will usually open a case for you.
Oct '16
-
I have recently replaced my nozzles, ptfe tubing and cleaned the gear wheels on my CTC dual's printer head. The stuttering of the filament feed happens...
Oct '16
-
I've just fitted new spring loaded extruders to my CTC dual printer and now they don't feed properly at all. The right feeds if the filament is pushed...
Aug '16
-
Where is your box from and what size is it please? I have been wondering how to create something like this for a nominal cost to hopefully help with AB...
Aug '16
-
Have had a few prints recently with PLA that look like underextrusion and the only way to get a decent print is to wack up the extruder temperature to...
Aug '16
-
I had a print that looked like that, was working fine and then went like the top of yours, turned out the nozzle was blocked. Unblocking wasn't straigh...
Aug '16
-
Have a look at this, https://all3dp.com/common-3d-printing-problems-and-their-solutions/ it has been really helpful for me. Re-level the bed using a pi...
Aug '16
-
Having trouble setting up octoprint on my raspberry pi 2 for my CTC Dual extruder printer. I've got everything working as far as the pi and octoprint a...
Aug '16
-
Have been trying to print several parts recently with rafts but for some reason not every part will get a full raft so when it goes to lay the first pr...
Aug '16
-
Apologies for all the questions. I'm wanting to use brims and skirts in a vain attempt to get ABS to stick, I have been using Makerbot for Desktop (lat...
Aug '16
-
I am wanting to know if I can replace the heat bed on my CTC Bizer Dual printer (230x150mm) with any generic bed or does it need to be specific to the...
Aug '16
-
Sailfish requires me to note down the X, Y and Z offsets as well as the Toolhead Offsets due to it being a dual printer. I have found this in makerware...
Aug '16
-
Hi, my 'pyrex' plate has finally arrived and fits perfectly. I've printed the Z-axis device that trips the switch at the correct height however I am no...
Aug '16
-
I have the standard CTC Bizer dual and am wish to flash the latest sailfish firmware but need to do the following " 6.3.1 Step 1: Before you install Sa...
Jul '16
-
Can anyone help? For some reason the front left corner of prints always seems to lift and warp and appears to shrink no matter whether it's in the midd...
Jul '16
-
Tried to print with both extruders but the left nozzle is too high and fails to lay the filament to the plate, right nozzle is perfect. What do I do? C...
Jul '16
-
How do I know what machine I have?? I just got ctc dual extruder makerbot /replicator clone but am getting a little confused what I actually have… Its...