Skip to main content
48 results for@gikam #3d-printers
Advanced filters
Relevance
Relevance
Jun '17
-
All my screws and switches were ok. Which switch have problem? what is the thickness of your switch? can u post some detailed photos? The only problem...
Jan '18
-
Anet A6 is a bit better. Prints excelent with proper settings, has fans for extruder and filament nozzle. I heated the bed to a bit more than 110 degs,...
Dec '17
-
or to the fan 
Dec '17
-
use Repetier host program
Dec '17
-
the nozzle and the hot 'cube'/assambly should not rotate
Jan '18
-
increase temperature and speed or turn off fan; otherwise the filament may block beacause of too low flow speed and it solidify before exit from nozzle...
Jan '18
-
u need to know the com port number which is created when u connect the printer and set it in Config > Printer settings. Do u know it?
Dec '17
-
Repetier host rises 15 mm on Z at the beginning of gcode.
Dec '17
-
print in the middle where is the front FAN duct?!
Dec '17
-
what is the Z distance for support? 0.2 should be good
Dec '17
-
i recommend using a screwdriver and level it manually
Dec '17
-
the screw is for setting the wheel pressure . To release the pressure and let the filament free (open the gear), just push the screw down.
Dec '17
-
large pieces tend to wrap more easy. Did the hairspray resolve the problem? Increase the temperature around the print. Enclose the printer. Reduce the...
Dec '17
-
why all of you buy A8 and not A6? A6 has a led on the bed which lights when is heating. If it is not on when u have 12V on connector then the soledring...
Dec '17
-
wow at last somebody witn an A6. but I didn;t have this problem. the printer shuts off while printing? can u turn easily the motors when it is off? per...
Dec '17
-
did it work with original configuration?
Dec '17
-
for ABS increase temperature by 5 degs. but first, be sure the bed is leveled (level it 3 times after 3 times homing, and heated to print temp) and bel...
Dec '17
-
the left Z can.t move. try rotating by hand and see where it blocks. remove the fan and check where it touches the case/grill.
Dec '17
-
I did fit a PCB drill on a A6. so it might be possible on A8, too, although there are different extruder carriages
Nov '17
-
Why all of you are buying anet A8 and not A6 which is newer and better?! try printing from a slicer like Repetier.
Nov '17
-
disconenct printer from computer remove sd card resatart printer what happens?
Nov '17
-
Why you guys all buy Anet A8, since A6 is newer and better (and cheaper)?!?
Nov '17
-
if it turns when u swapped then let it so.
Nov '17
-
or even the newer Anet A6
Nov '17
-
does it happen if u move the head from the printer's panel?
Oct '17
-
PLA does dissolve in chloroform, like ABS in acetone. good luck
Oct '17
-
I think u have a Z wobble; your vertical threaded rods does not rotate around the vertical motor axis, not aligned. check the Z couplers. check some un...
Oct '17
-
Man, u changed the X/Y cables. put them in correct connectors.
Sep '17
-
I can't see much from the pictures. Perhaps you have Z problems. Check the vertical (Z) rods are firmly fixed to the Z motors.
Sep '17
-
Sorry , mate. If you changed the extruder and the motherboard, there is no more a Anet A6 printer. So i think you might ask the question elsewhere. any...
Aug '17
-
The fact that the printer resets when you preheat is a sign that the power supply may have some problems, When you switched to 110 v u sureley damaged...
Aug '17
-
I recommend an Anet A6, is newer and a bit better. I got mine from Aliexpress
Aug '17
-
Or you can measure the broken one
Jul '17
-
how does it look printing in another slicer? check printers setting about x/y axis
Aug '17
-
Please specify the printer model and add some photo
Jul '17
-
how do you know Ramps 1.4 is compatible with the original anet A6 board? Where did you get it from? _(_i can't see the filament in you movie)
Jul '17
-
change the filament check the settings for diameter and temperature
Jul '17
-
I use 97-105 bed temp for ABS. Dimafix for adhesion. ABS 'siroup' is very good, but is harder to clean. The most important is leveling!
Jul '17
-
what material and temperature u use?
Jul '17
-
all steppers are disabled?
Jul '17
-
the image is not clear enough. what material do you use?
Jul '17
-
Hi Is there any documentation about the menu items on the control panel on Anet A6 printer? What model is the main board of Anet A6? are there any prob...
Jul '17
-
I think your laser thermometer is wrong. try touching the nozzle with a drop of water. does it boil/sizzle? try touching the nozzle with a bit of PLA f...
Jul '17
-
I think u have a connections problem Z and Z' motors move together when the printer is powered because of current induction. check the picture: a8.png
Jul '17
-
the same file prints the same bad pattern always? any abnormal noise?
Jun '17
-
What about Anet A6? which is cheaper and bigger print size
Jun '17
-
HI I use A6 and Cura too try usual settings: 40 mm/s, 20% infill, 0,1-0,2 mm layer height, 100% flow, 100% feed, walls 0,8/1,2 mm (multiple of nozzle)...
Jun '17
-
I removed the original tape from the beginning. U can use hair spray, paper glue stick, ABS 'juice' (dissolved in acetone), or special adhesion spray "...