-
Hi, I’m working with an Objet24 and till yesterday all was fine. One day I printed a lot of articles. Next day morning the printer-program in the embedded WindowsXP (alaris.exe) starts, is shown in the status line for a couple of seconds and… dissapears from status line. No start, no printer contro…
-
Hi Dave, I own an Objet24 not a 30pro but the 24 is more or less identical. Have you run the weight test? And if, how many grams is the weight of the outputted support or material? I think you first have to make sure that weight test puts out ca. 5 to 5,3g (thats the correct value on my machine) p…
-
Hi Lee, don’t worry about asking me a lot - in the past I did that with my service technician and he was very generous with his informations in the beginning of my service contracts in the first two years. Meanwhile I don’t have a contract, my machine is five years old and all (well, the most…) run…
-
Hi Lee, congratulations - sounds like an improvement! I print a lot and cleaning and greasing (very thin) the rails of X, Y and Z (dont forget the Z-rail of the tray) is done once a week. But NEVER grease the ball screw spindle at the Y-axe. Greetz, Edgar
-
Hi Lee, was the mousepointer in the lower right corner while pressing Ctrl+Alt+m? If not, the warning message will appear but NOT the new menu item. So try again: - click right in the middle of the remote window to make sure that the window is active - mouse lower right corner - Ctrl+Alt+m If i…
-
Hi Lee, what I meant is the remote window of the embedded Windows XP inside the objet (see pic1) not any window in the local Objet-Studio-Software. Click into the middle of that remote window, then move mouse to lower right corner (big red arrow in pic2) and press Ctrl+Alt+m, then a warning message…
-
Hi Lee, as far as I remember you can get into the maintenance menu not with a password but with the key combi Ctrl+Alt+M when the Objet window is active and the mousepointer is in the lower right corner of the window. But again: BE VERY CAREFUL if I remember right and you can enter the maintenanc…
-
Hi, I don’t know a third party source for model material for the Objet but for the Support-Material. Look at The support material is packed in Eden-cartons and I refill my Objet bottles out of these Eden-packages. I’m completely satified with this cheaper material. Also offered at ebay in Germa…
-
Hi Lee, yes I purge manually. That can be switched within the maintenance/Parameters Settings menu, see picture. But always be VERY CAREFULLY what you change in the various maintenance menus. You can ruin all within your printer. As I remember, here in the forum is anywhere described how to switch…
-
Hi Lee, I do not really have a solution, but a workaround in that way: - Purging (I always purge manually before the first print, not automatically) - Open cover and push the printing unit slowly forward until stop - Then Push the printhead unit all the way to the left stop - Then Push the prin…
-
Hi, in Dec 2017 the vacuum value of my Objet24 fall down sporadically to 4.1, goes up again, dowen up… Then I drove the machine head to service position, switched the print er OFF and did a reserch in the web. Fortunately I found this thread and especially the link to it was very helpful. I deas…
-
Hi, oh YES, you’re absolutely right - printer type WILL be helpful…
I’m using a Stratasys Objet24.
Maybe there’s one out who can help.
Best regards,
Edgar -
Hi Jason, I know, you’re question ist already 7 months ago but maybe some other user finds this thread, so here is my answer: On my Objet 24 I had the same problem, The temperature goes up and down but never reached the correct value of around 71 degees celsius. First I tried the not so expensive…
-
Hi, I searched in the knowledge base, but couldn’t find an answer to the following error message: Pre-Print error - MCB Right limit (-10020) end print Before that: - Purge done - start - UV lamp turns on - Initiating moves in all axes - UV lamp turns off and the error message appears This e…
