Apart from all the good adivse you have gotten, to improve maker-ware download prof-tweak from nothing lab. It provides substantially more tuneability, its free. I used it for about 4 month, got comfortable with the printer and was getting very good prints until i wanted the versatilty of s3d for its support. In thingiverse i put a ctc nozzle calibration which really helped me tweak my nozzle with proftweak. Good luck
Skip to main content
Okay - So here is attempt 6 results with the following parameters:
Attempt 06
filename: pilot06
Extruder: 190 c
Printer Bed: 50 c - With Wickes Heavy duty masking tape (interior and exterior)
Speed while travelling: 100mm/s
Extruding speed: 40mm/s.
Room temp: 15.3 C.
It all seemed to be going well, It adhered to the tape very well. the Top of the hat came out much better than before. But half his face and right shoulder are missing with the above settings… pictures below:
So I thought id adjust some settings and try again…Here is what ill be changing (in bold)
Attempt 7
filename: pilot 07
Extruder: 190 c
Printe Bed: 40 c
Speed while travelling: 100mm/s
Extruding speed: 20mm/s.
Room temp: 18.5 C
I wonder why the hat turned out better, but the face turned out worse. I’ll post results of attempt 7 when I get them.
hmmmm (confused :-/)
I don’t think you need to slow it down more than 40mm/s, but if if works it works… the side still looks like a heat problem so try turning off the bed heat all together and see how that turns out.
2 suggestions to try. First try rotating it in the y axis so the face is opposite where the right side is now, it could be that the right side is being exposed to more heat or there is more airflow across the left side. Second, try slicing is along the middle and print it as two halves. This could help since they won’t print so high and change the slice direction some.
Okay, so basically the printer simply will not work unless I find some way of printing the thingiverse ctc printer fan duct and install an additional 24v fan?
The problem here is that I cannot print the fan modification duct as the printer doesn’t work well enough. You need cooling to print the cooling! Catch 22!
Unfortunately there’s no magic answer here. This will all depend on the type of plastic being used. You will find there is a sweet spot. 5 house fans might be a little overkill, you will need some heat to get good inter later bonding, but then it must cool before the next layer. The print head is also a source of heat that will deform the lower layers. For your particular situation, a fan blowing across the printer, as well as a 20mm cube as tall as your model. This second model will pull the print head away for a bit of time.
The fan pointed at the motherboard is a good source for that fan. It was put there by makerbot to address a voltage regulator problem that our bots don’t suffer from. Generally you print a second duct with your first poorly printed duct, with much better results.
Have you calibrated the nozzle like I mentioned? Holes are usually under extrusion. How’s your extrusion multiplier?
again I suggest proftweak. Many people will be able to help you tune the printer. If you don’t have the y pillow blocks I suggest you download and print them as well. Will improve printing substantially. Your problem sound like tuning, the printer out of the box is decent enough with proper tuning. I did not have decent prints until I calibrated the nozzle, mine was over extruding.
Do not point fans at it, that will cool the extruded and your print will fail due to clogging or the firmware will stop the print for the inconsistent heating
The fact of the situation here, is a rookie user is attempting to print an advanced model on a bottom of the barrel knock off of a clone. I am not saying that this is impossible, but this is not a good start print. Overhangs, unsupported hat brims, facial features, this is a very complex model being printed. Redirecting to Google Groups 4 This is the Google group, that I manage, you might find some good information here. In a much easier to read format.
Hi Adam, agreed, I certainly am a rookie user!
I didn’t know that the model i was attempting to print was an advanced model, I thought it didn’t matter what it was you just load the model and print it. and if the temperatures are correct and bed is levelled, everything should pretty much work out of the box. But since learning that the model I am trying to print is a bit more of an advanced model it makes me feel a bit better that I cant get it to work after 8 attempts!
I’ll do as I’ve been told as well and calibrate the nozzle, download proftweak, and make some pillow blocks. I’ll get on over to your group on Google as i presume i’m not the only person struggling to get good results with this printer.
I have to argue the point about this printer being a bottom of the barrel knock off. I thought this printer was rated the second best printer on 3d hubs? That was the basis on which I bought it. 
Ah haa - I get you. I’ll get all the nuts and bolts mentioned on the Google link above and do that mod as well.
That is the next thing on my list. I figured i’d get the basics done right, like levelling the bed and getting the temps right. but yes this is important. I’m not sure what the extrusion multiplier is?
I have downloaded, installed and run prof tweak. I have duplicated a profile (the Makerbot PLA Standard) and saved it. and opened my new custom profile in Proftweak, and can see all the different settings.
I’ll get on with calibrating the nozzles and i’ll also download and print pillow blocks (i’m not sure what these are yet!)
With regards to Nozzle calibration. from my Googling it seems like the Nozzle calibration is to calibrate the distance between the two extruders. I found a post on thingiverse about nozzle calibration. But it doesnt say how do do it, or what model to print. Is there a guide anywhere on how to calibrate the nozzle?
Thanks for your patience!