Skip to main content
50+ results for@keebie81 #3d-printing
Advanced filters
Relevance
Relevance
Jul '16
-
https://www.reddit.com/r/3Dprinting/comments/4pekuo/i%5C_cant%5C_replace%5C_the%5C_print%5C_build%5C_tak%5C_on%5C_my%5C_wanhao%5C_i3/ reddit https://ww...
Oct '18
-
None. 3d printed toys are not baby suitable. They will be putting them in to their mouth and parts break easily. Buy safe toys that are already tested...
Dec '18
-
Looks too close to the bed
Dec '18
-
You can contact the manufacturer. They should be able to sell spare parts.
Dec '17
-
Are you using the default cura profiles? Sounds like retraction might be set to high. You can always call tech support, I believe they are 24hrs
Nov '18
-
The problem is LEGO bricks are within tolerance of 0.01mm, You will likely need to look at dimensions and recreate them to get them to work for you. Ma...
Nov '18
-
I have got surface issues like that if I have two printers running on same table. I keep all my lulzbots on their own shelf unit or table because of it...
Oct '18
-
Which white? I have gone through a lot of the warm white with no issues in 1.75 and 2.85, I print at 200-210 typically. I have used both Titan Aero's a...
Oct '18
-
Have you tried contacting Makerbot support??
Sep '18
-
The display should show the temperature it is reading. When you say it cant go above 235 does the display not let you pick a higher temper or does it n...
Sep '18
-
Maybe an easier solution would be load it in simplify 3d. then sink the part you dont want printed below the bed. Or edit process to stop at certain he...
Sep '18
-
Also depends on the motion system used. On my BCN3D SIgma I tried some bearings instead of a metal sleeve for the y axis and could hear a noise differe...
Aug '18
-
If using cura you can experiment with the fuzzy skin settings. https://ultimaker.com/en/resources/20426-experimental
Jul '18
-
Top/bottom layers will only cover the portions of the model. An example is the letter O, if you print this with 2 top/bottom layers it will not fill in...
Jul '18
-
Check belts and set screws on pulleys to make sure there is no slippage. Watch it print and see if anything is causes the hot end to get caught and shi...
Dec '17
-
I have a Lulzbot Mini and it was quite easy to setup. Once it was out of the box it was printing a perfect rocktopus right away. The one benefit over t...
Dec '17
-
Looking at the product page I did not see any specifications with operating temperature listed. Might be a good idea to contact the company and see if...
Dec '17
-
I do not know of any printer that is also a 3d scanner. they both operate completely different and a good scanner is way more than 2k
Dec '17
-
It looks like z-banding, check out this youtube video and try the mods to improve it https://www.youtube.com/watch Z-Banding Fixed! - Improving the MP...
Dec '17
-
Martin, Where are you located. That will help people know if you are in same country and possibly help. Are these your own design? its easier to sectio...
Nov '17
-
Have you tried contacting the company that makes the printer or sold it to you?
Dec '17
-
Have you verified that your esteps are correct and that its not over extruding? You could also try turning the flow multiplier down a few percent
Dec '17
-
ABS needs an enclosure for larger prints. Because when abs cools down it shrinks slightly, if the other layers are still warm when previous layers are...
Dec '17
-
ive had great results on my printer spreading a layer of liquid all white elmers glue, let that dry. Set bed to 100 and then print the part on a raft....
Dec '17
-
We cant help without more details, pictures are always helpful along with settings used
Nov '17
-
Can it use standard 1kg rolls? Looking at your website it appears you uses a smaller roll that only you sell.
Jan '17
-
How tightly wound is the spool of filament?
Nov '17
-
You should try finding the manufacturer of the printer and see if they sell parts
Nov '17
-
That section missing is most likely thinner than the nozzle diameter. So it doesnt show up. Or theres a problem with the geometry of the stl. What prog...
Nov '17
-
Some pictures would help to determine if its a adhesion issue or a first layer height issue. When I had previously used a kapton tape bed I had better...
Oct '17
-
You can always look at the changelog to see whats new https://ultimaker.com/en/products/cura-software/release-notes
Sep '17
-
Cura is another option
Sep '17
-
Any 3d print on a fdm printer wont be perfectly clear.
Apr '17
-
From this article it looks like it may cost around 5,995 https://3dprintingindustry.com/news/64028-64028/ 3D Printing Industry-The Authority on 3D Prin...
Apr '17
-
I weigh a similar empty spool and then weigh the spool of leftover filament and typically can make a good estimate to amount left from that. Then use t...
Jun '17
-
The steps per mm are set at 100.5 for the x and y in the firmware. Change it to 100
Jun '17
-
Im in the USA and still see colorfabb and filabot. Proto-pasta is missing
Jun '17
-
For the PEI bed Lulzbot recommends removing PLA prints at 45c. They have the end gcode set so the bed stays at that temp after printing. The prusa is f...
Apr '17
-
I strongly disagree with your take on this. An example is a car manufacturer, they cant void your warranty if you use some other brand gasoline and a p...
Apr '17
-
Is there a step for calibrating the offset of the dual extruders?
Apr '17
-
I would say no, that marvin looks terrible. How would you feel if you paid for an order and the print looked like that.
Apr '17
-
Are these printed on a raft? If not your nozzle is too far away from the bed it looks like
Apr '17
-
you dont use a spirit level for leveling the bed. You are leveling it to the nozzle and making sure that its the same distance or fairly close in multi...
Apr '17
-
Its probably the bearings going out on the fan. Eventually it will die and stop providing cooling to whatever it points at. If its the hotend it will j...
Apr '17
-
I would recommend a hub with SLA printing. Heres some SLA printers near you. https://www.3dhubs.com/3dprint#?place=New%20York,%20NY,%20USA&latitude=40....
Apr '17
-
You should print it at the height specified in the order request. This is simulating a customer order. Your quality, communication, speed and service i...
Apr '17
-
Typically Ninjaflex doesnt need a heated bed, but ive found i get warping on a longer print. I use 50c with great results on a glass bed
Apr '17
-
You could always contact the companies that make the material or find hubs that already offer the material and make an order from them.
Apr '17
-
Check out http://reprap.org reprap.org
Sep '16
-
Also the 3d printed will not be as strong or look as nice as a molded part. Depending on the use you do not want a toy that could break in to small par...