3D create and print (eagle moss)

andygreyrider · 2016-09-30T14:00:54.000Z

Hi Everyone, I just wrote to Eaglemoss and Dbfactory to inform them that, after many promises they had failed me and I am going to stake a claim via the County Court. There’s no template as, everyone’s case is different and we all have various issues with them. Just inform them of your intentions to seek recompense via the County Court. If you send me your problems to my email address andygreyrider@googlemail.com I will draw up a general statement to present at County Court. If you wish to follow my lead. After you have informed both parties of your intended court action, I have been advised to ignore them like they have us. This is likely to panic them into offering as little, as possible to squirm their way out. In the Sales of Goods Act you are advised to give them reasonable time to repair or replace. Then you are free to pursue them through the Courts for a full refund. On the Compensation Element; we are within our rights to claim for Stress and Anxiety, as it is with many financial claims. If it has caused business problems then, you are within your rights to claim for lost business. Under the new Distance Selling Regulations they are in breach of. For supplying faulty software et cetera. I am very experienced in making claims against vendors and a Consumer Champion with many wins! Please get in touch the sooner the better and the sooner you get your money back. I want my money back and to prevent them from hurting other’s! I promise you that no out-of-court settlement will suffice. I have never backed down and have been facing obstacles like this my whole life. Kind Regards Andrew Millard

Barry_Finn · 2016-09-30T16:28:16.000Z

Hi Andrew

I would be grateful of any assistance I can get to pursue this as the more I see the more I realise that I am not a one off case.

I contacted the ‘support team’ yesterday and received an automated response that they would be in contact within 24 hours (not holding my breath).

My faults so far.

‘pause’ button on the front of the printer stays solid green and does nothing.

I have power (according to the lights) but no control from the lap top I have bypassed the hood switch as directed reset the printer, tried different cables, uninstalled and re installed and disabled and re enabled the ports etc.

When I initially managed to get it to work and raised the print bed I noticed that even if it did work properly that I would not be able to calibrate it as the clip that holds the plate to the bed lines up perfectly with the the nozzle thus not allowing the correct clearance to be achieved.

I am not sure if it is relevant but would like to find out, but I have purchased an Arduino Uno board as suggested on various posts (I am not going to use it in the printer though) and found that the input voltage is recommended to between 7-12v with a maximum of 20v https://www.arduino.cc/en/Main/ArduinoBoardUno (I can only assume that the board supplied will have similar requirements) however, the power pack supplied to do the testing is rated at 24v.

I am wondering if it is worth starting a new post (linked here) to make it easier to find and keep updated.

Barry

batryhak@gmail.com

07769871406

andygreyrider · 2016-10-01T00:51:13.000Z

Hi Barry,

All the balony about the lid switch is total carp.

You can disable it in the software settings. So, none of this depressing the lid switch.

I need everyone’s story of problems.

Going into your email account and search for Eaglemoss and Dbfactory. You need to forward these to my email address if, you wish to have a class action template.

I am very serious about ‘no contact’ with them once, you have exhausted their chance to correct your problems.

I have had all the emails you are talking about and they can’t tell their R’s from their Elbows. They can’t even communicate effectively internally, either it’s a case of Chinese Whisper’s or you end up repeating yourself.

They are expecting us to give in to their fun and games.

They have sold us a piece of poo, based on the Reprap design and I can assure you, you don’t need a hood to print ABS successfully.

Everything they have commissioned with the Vector 3 is flawed.

If your new filling fell out by the dentist. Would you accept it if they said come back next year or see another dentist?

This is what Eaglemoss and Dbfactory are up to, passing us from pillar to post and back again.

We shouldn’t have to seek out our own fixes. We paid for a product and it’s not fit for purpose. How much anxiety and stress, not forgetting time, have you left?

Would they put up with it?

We want our money back and compensation.

My dear late Uncle, who recently passed away, used to quote ‘the squeaky wheel always gets the oil’ and this what we are ‘the squeaky wheel.’

Kind Regards

Andrew

andygreyrider · 2016-10-01T01:31:32.000Z

Hi Everyone,

It is not your duty to fix their mistakes.

If you want to stick with the Vector 3 piece of carp, that’s your prerogative.

If you want to salvage it, it’s a lot of tat for £900.

I cannot twist your arm to join me.

Hopefully, if you do come along for the ride, you were wise enough to keep all correspondence with Eaglemoss and Dbfactory and recorded every telephone conversation.

I personally have taken names, position in company, and digitally recorded every telephone conversation for the last 33 year’s.

I am not like any typical Englishman, letting it slide, I am very much American in that, I complain, claim and offer praise where it’s due.

You’re not alone if you would like redress for any situation. If it’s offered, use it because, you’re guaranteed someone will have their Ten Penneth out of you!

Another option is to go to your bank and ask for a draw back of funds. Banks are very good at this type of thing.

If like me, you paid with a credit card maybe, a claim lodged with them.

There is so much legislation these days geared for consumer rights protection.

Hey! If you don’t ask, you don’t get cliché, nearly always works.

I still want redress through the courts, don’t you?

Kind Regards

Andrew

anon36107456 · 2016-10-04T20:55:14.000Z

[post deleted per user request]

anon36107456 · 2016-10-04T20:57:08.000Z

[post deleted per user request]

Graham_Tanfield · 2016-10-04T21:08:25.000Z

I get the same problem with the print head sliding to the left and the bad vibration/drilling noise which I was told by the IT geeks to send photos or a video,not sure what a photo will do lol .My reply to that was even if I did send a video it still won’t fix the software problem .I got a reply today saying they are updating the software soon and they will let me know soon

Peter_Over · 2016-10-07T08:58:33.000Z

Hi I have just completed my 3d printer from Eaglemoss It was hard to calibrate but found best to use a larger object rather than the 02mm gauge say 75mm high with the build plate at a lower level then when level raise the plate until reaching the 02mm gap This made it much better to level the plate the only problem I have is the bed plate will not heat I have resolved this problem by getting PLA from Rigid ink. I now get very good results as Rigid ink PLA will stick to a cold bed.

I would add that getting the bed plate level and at the right distance from the extrude is very hard.

Peter_Over · 2016-10-09T07:12:51.000Z

Hi i had the same problem but then found i had fitted the brackets on the wrong side instead of between the fan and block this raised the fan blower but the clearance is very small and i did need to bend the brackets a little but all works fine now

Danny_Hardy · 2016-10-12T07:52:19.000Z

Guys I think this is due to the limit switch not being pushed in fully when it moves to the egde

Danny_Hardy · 2016-10-12T07:54:02.000Z

Is anyone having any problems with grub screws coming loose after a few prints? which then causes the printing to go out of line and I wondered if anyone had any solutions for that? I am thinking metal glue

Danny_Hardy · 2016-10-12T07:54:41.000Z

.

anon36107456 · 2016-10-12T15:54:53.000Z

[post deleted per user request]

anon36107456 · 2016-10-12T15:55:32.000Z

[post deleted per user request]

Danny_Hardy · 2016-10-12T16:12:57.000Z

Well i have fixed it by removing the bottom screw of the plastic plate/grip that holds the limit switch in place. Pushinh it as far right as possible and glueing it in place. Its just because its about 1mm out. You can test it by moving the x-axis left and right to make sure the limit switch clicks when it reaches the end

Danny_Hardy · 2016-10-12T16:16:41.000Z

Ive found you can buy grub screws online woth threaded locks to stop them coming undone with vibrations. Im guna give that ago if not threaded lock glue seems the way

Danny_Hardy · 2016-10-13T10:28:22.000Z

accu.co.uk

M2 x 4mm Flat Point Set / Grub Screws (DIN 913) - Thread Locking A4 Stainless...

Buy M2 x 4mm Flat Point Set / Grub Screws (DIN 913) - Thread Locking Marine Stainless Steel (A4) from Accu's Precision Screws range. Manufactured by AccuLock. Available on a short lead time with express worldwide delivery available.

I think this is what we are looking for. I have ordered some so I will soon find out.

Graham_Tanfield · 2016-10-13T11:09:22.000Z

Still having trouble with the printer and software,the damn thing still vibrates as the printer head tries to go further to the left than its supposed to and the software still doesn’t tall to the printer so nothing prints.I have emailed both the tech guys and Eaglemoss with very little in the way of a solution and I also tried calling both the v3 customer services and technical help and was on hold for 10 minutes on each so I gave up. A refund is what I want now as it’s turned what I thought would be a good project and product into a large paperweight.Rant over

anon36107456 · 2016-10-13T11:13:33.000Z

[post deleted per user request]

Danny_Hardy · 2016-10-13T12:18:36.000Z

Graham, the problem with the damn thing still vibrates as the printer head tries to go further to the left than its supposed to is a problem with the limit switch not being being pressed in fully, I put my fix below. You need to make sure it fully clicks as the print nozzle arm inside the metal case pushes the limit switch down.

If it is fully clicking and being hit every time and not being pushed back away then you will have a problem with the limit switch but either way thats what the limit switch is for and that is the reason, it is there to say " this is the end, stop moving in this direction "