Mid-print stopped

3D Printing

Apr 18, '19

I dont know why, I wanted to print something and simply the print stopped midway, and thsi happens every time. Also below I posted the photos of the prints, why is it so messy in one of the parts? What can I do? I use ABS at 240 degrees with 90 degrees bed temperature. [IMG_4252] [IMG_4270] [IMG_4…

2 problems with something

3D Printing

Apr 14, '19

Lately I wanted to print something, as always with my ABS at 240 Celsius degrees. I moved my printer into a smaller corner but I dont know if that changed anything. I am wondering if this is a problem showed below caused by temperature or maybe something else? I would greatly appreciate help in this…

Problems with printing and filament

No category

Sep 29, '18

I suppose the part on right moved a bit but I dont really know why it moved as the adhesion was perfect I can say, it is like it got moved by the nozzle or something as why would it unstick when also the part unsticked was stragiht (there was no warping so no typicall unsticking)

Problems with printing and filament

No category

Sep 24, '18

Sometimes i get very strange result when printing which is not desirable as it ruins whole project, here are some photos of it, what may be the cause of that? I use ABS with heated bed and glass with glue as bed [IMG_2314] [IMG_2315]

Clogging

No category

Jul 21, '18

Lately I have been printing a figurine and after 1/4 of the print the proccess went on but the filament stopped flowing out and the nozzle was way above the print so it stopped at some point. There was no big clog on it, just the tip was a little covered so I cleaned it and started again (maybe it w…

Bubbles

No category

Jun 28, '18

Lately I noticed that there are some “bubbles” that you can clearly see on the photos below. How is that happening and how to take care of it? [img_1460.jpg] [img_1461.jpg] [img_1462.jpg]

Weird problems

No category

Jun 23, '18

I have seen things like this very rarely but lately it became more common. I want to ask why there are some “bubbles” like seen in the first photo, as well as why the filament is curling so much on another ones [img_1419.jpg] [IMG_1418.jpg] [img_1430.jpg]

Bottom parts above supports problem

No category

May 31, '18

Lately I have printed a gadget from one game, the first one is gray and what I saw is that two out of four arms of it were very badly printed on the bottom side. What I thought was that the supports were parallel to these arms so that they couldnt really print well. That is why I decided to rotate i…

Filament not flowing properly on part of print

No category

Apr 16, '18

Lately I printed a thing and there is this like “squeezed” filament and i dont know why it comes out like that, I tried lowering the bed but then it just doesnt stick to it. What should i do? (photo included) [img_0788_1.jpg]

Filament not flowing

3D Printers

Apr 2, '18

Lately in my da vinci pro 3in1 the filament is not flowing out. The nozzle is not clogged for sure neither the temperature is too low/high for the filament. The whole process is going on, sometimes a little bit of filament flows out but after like even 2cm it stops and doesn’t extrude anymore. Solut…

Thing on the left

No category

Feb 27, '18

I wanted to ask what is going on on the left side of the print on photo, it sometimes happen to me on different sides and in addition the bed is calibrated and everything should be well printed [img_0104.jpg]

Problems with printing

3D Printers

Feb 11, '18

Something shown down below happens to me. What can be causes of this hapenning? I use a coropad, my davinci pro 3in1 is calibrated well, I use ABS on 240 degrees nozzle and 90 degrees bed; I also have my printer closed completely. If any more details are needed just ask I will try to do my best. […