Lock Nester Certification - Best Practices

gregh · 2014-10-05T18:28:39.000Z

Sorry, to clarify the setting is in Expert settings and its called “Overhang Angle for support”, the default is 60.

I stated it the wrong way round in my original post. Making this angle LOWER ADDS support of course, and HIGHERr REDUCES support.

martinv77 · 2014-10-07T15:18:28.000Z

Hi @fleethower,

I was asked by Luuk to get in touch regarding a problem I’m facing with the certification print of Monica. The printing seemed to work fine with good quality, but when completed and after minimal processing and removal of the flashing and support it seems the model does not stay together. I’ve been very carefull not to remove to much material, but still Monica falls appart. Do you have any tips/sugestions to overcome this issue…

Thanks,

Martin

IMG_0286.JPG1608×2044 691 KB

martinv77 · 2014-10-07T15:21:35.000Z

@fleethower

fleethower · 2014-10-07T16:27:01.000Z

Hi Marinv77, the print quality looks good. That piece can be a bit loose, but they should hold together. I’m wondering if you haven’t smoothed the connections enough where the supports were. I’ve run into problems when not sanding enough, but have never run into any problems by sanding too much, try smoothing those areas a bit more. Let me know if that helps, this looks like an ultimaker, correct?

fleethower · 2014-10-07T16:40:05.000Z

Hi Greg and Maikel, you should have recently received a file with the supports already included, so that you won’t have to generate any in cura. This should make the printing go more smoothly, please let me know if you haven’t received that file.

Thanks!

martinv77 · 2014-10-07T17:00:51.000Z

Yes indeed Ultimaker 2…

I will try sanding a little more than and see what that brings.

Thanks

Martin

martinv77 · 2014-10-07T19:25:28.000Z

Hi I tried your tip and it worked.

The pictures are now submitted to 3Dhubs for review.

Thanks again,

Martin

IMG_0290.jpg2046×1636 855 KB

IMG_0289.jpg2020×2048 1.08 MB

IMG_0292.jpg1536×2048 864 KB

fleethower · 2014-10-07T19:29:32.000Z

Hey Martin, great, I’m glad to hear it. Your print quality looks fantastic, thanks for being a part of this project!

carter2422 · 2014-10-07T20:25:02.000Z

I had this problem as well, although it was not due to sanding. My problem is that the head piece was much too loose, causing it to fall off unless the whole piece or orientated upwards.

martinv77 · 2014-10-07T21:35:16.000Z

There is one more trick you could use, but be carefull as it can potentialy ruin your print.

Try holding the lips of the head piece under hot watter and gently squezze them together so the get a fraction of a milimeter tighter. This gave the final result for me.

Again, be carefull

Martin

Joerg_4 · 2014-10-11T10:15:02.000Z

Hi all.

here is my result of Lock Nesters Monica.

Printed in faberdashery “cherryblossom pink” and ColorFabb “fluorescent pink”

btw: After earning the badge, how do we get the other Lock Nester Models for test prints?

IMG_2374.jpg800×541 46.1 KB

fleethower · 2014-10-11T21:06:18.000Z

The certification model is just Monica, she is the toughest print to make. Once certified you will receive the final models around October 20 or 21, but test prints for those models should not be necessary unless you would like to conduct them on your own.

Best,

Fleet

Fenix999 · 2014-10-12T14:48:03.000Z

I woudl like to give it a try with this certification, how can I find the files?

Thanks!

Joerg_4 · 2014-10-12T18:37:04.000Z

Hi Fleet,

thanks for your reply. Sure test prints may not be necessary, but I like it to practice (print and post processing) to be prepared when an official order is placed.

Besides that, collecting all and take a photo of the entire “family” would be fun too

Cheers,
Joerg

fleethower · 2014-10-12T19:28:05.000Z

Hi Joerg, sounds good, we’re working on the models furiously to get them all finalized, if it’s possible to distribute we will absolutely do so.

Thanks for you interest and help with this project!

Fleet

Nicolinux · 2014-10-15T22:20:54.000Z

Hi,

Quite a few people asked about the certification .stl files. So how/where can they be downloaded?

Thanks,

Stefan

lidela · 2014-10-17T12:16:53.000Z

Thats great idea!

I would also like to get certified for Lock Nester.

How can i get in the certification process and get the .stl file for Monica?

Ara · 2014-10-20T04:41:38.000Z

Hello everyone, @fleethower,

I have printed six Monicas and gave them to my kids to play with for “market research” (ages 9 and 11). The tail keeps breaking off so I would like to propose making the tail removable. It could also have a long and wide base inserted in a hole. Also, the coli should be thicker diameter. So, is it possible to get the CAD file to make the modifcation? In addition, maybe the tail could be customized to different shapes or be the kids name in script font.

Thank you,

Ara

fleethower · 2014-10-22T20:01:11.000Z

Hi Ara, thanks for your interest and testing! We have been furiously trying to finish all the models and have just done so. The tail modification is a great idea, will look into that asap and see if new files can be distributed to the hubs.

Thanks!

Tiguu3D · 2014-10-27T05:53:03.000Z

How do I get certification?