Cubify Printers

Just3D · 2016-12-14T17:04:25.000Z

I’ll do that. I just found this on the kisslicer forum Cube (3rd Gen)??? - kisslicertalk.com

Just3D · 2016-12-15T21:48:24.000Z

Spencer, here is a pic of my benchy. Hard to show in red filament

img_20161215_164037183.jpg2592×1456 491 KB

ROBERTOGEHLEN · 2016-12-20T18:01:13.000Z

Now available chip reseter for CubePro and CubeX … no connections to printer required … www.cube3dfree.com

SpencerR87 · 2016-12-20T19:15:54.000Z

I use the cube 3

ROBERTOGEHLEN · 2016-12-20T19:39:16.000Z

Soon we will have a low cost solution for Cube 3 …

Just3D · 2016-12-20T20:18:35.000Z

Be careful about purchasing this expensive device. With all the research I have done I have yet to find anyone who has purchased it and is using it successfully. I have read a lot of warnings about it tho

ROBERTOGEHLEN · 2016-12-20T20:52:55.000Z

I agree, everybody must be careful. We have customers using the devices on more than 46 countries since 3 Years ago. If someone would like to purchase just tell us your location, we will forward 3 customers close to you using the devices.

ROBERTOGEHLEN · 2016-12-20T21:56:21.000Z

Another comment, there are many false supposed feedbacks from customers planted by 3DS, by a simple reason, they still want to sell the stock of plastic with price of gold, so if people become afraid, increase these evil sales

ROBERTOGEHLEN · 2016-12-20T21:59:50.000Z

So the last comment, all the sales are by PayPal, what gives 100% moneyback warranty … so very strange, 3 Years, 46 countries, the devices don’t work ? afffff

Just3D · 2016-12-20T22:05:34.000Z

I want nothing more than to find a lesser expensive option - I own two cube 3’s. But I do not want to throw that much money at something only to find it doesn’t work. So based on that I need some level of comfort that it really does work, and after looking a bunch I am not even close to being there.

Just3D · 2016-12-20T22:34:06.000Z

I’m just saying I am looking for evidence from other 3D systems printer owners that they are using your device and are happy with it. I cannot find any.

ROBERTOGEHLEN · 2016-12-20T23:47:48.000Z

You will find on the net angry people or false information. Satisfied people just use and be happy, don’t think to post affff

ROBERTOGEHLEN · 2016-12-21T00:00:45.000Z

We are developing a low cost solution, so ASAP I will let you know … thanks

SpencerR87 · 2016-12-21T00:16:23.000Z

How far off are we? Cube3 users are ready to ditch the system and move on and not wait

ROBERTOGEHLEN · 2016-12-21T06:26:49.000Z

fuck

ROBERTOGEHLEN · 2016-12-21T19:34:05.000Z

I know that the time is a problem, but the intention to put an encrypted chip to make the printer slave of the original cartridges is to delay the bypass system

PDXDDD · 2016-12-22T21:26:05.000Z

Hi josh, are you trying to print the original files that came with the USB stick? Make sure they are good because they were sent out wrong from the factory

Just3D · 2017-01-04T18:04:49.000Z

Spencer, I sucessfully completed the filament hack last week. Using an empty modified cartridge to feed the standard filament and a 1-3% full cartridge for tricking the printer. I have a video that I will post maybe this week, but to give you the process so you can try yourself here it is:

1. Insert the 1-3% cartridge and start a print (1-3% is important because the printer will notify that there isnt enough filament to finish the job)

2. Select the checkmark to proceed

3. When the screen says apply glue, remove the cartridge and replace with the hacked cartridge. (dont forget the glue)

4. Select checkmark to proceed (the printer will begin the heatup process and begin the print)

Important to remeber:

1-3% cartridge, hacked cartridge and standard filament all need to be the same material- PLA for instance.

There are a few different ways people have hacked the cartridge, but I chose the simple way. Drill a hole near the bottom of the cartridge at an angle (toward the extruder). This is so you can feed the teflon tube that guides the filament to the extruder thru the cartridge casing (cartridge does come apart for access to the teflon tube which you already know if youve had to fix a jam). Feed the standard filament into this tube up thru the extruder and to the hot end. You will need a spool holder for the standard filament.

One thing I do not know yet is how different colors act. I say this because I was charting temps on the 3D systems filament and they seem to vary a bit and also ran at higher temps than typical. The standard PLA I ran though was right in the middle of the manufacturers recommended temp range, so I was happy about that. I used Inland Neon Green.

Hopefully the video will help clarify if necessary, but feel free to ask questiion if needed.

SpencerR87 · 2017-01-04T18:42:52.000Z

Rick I’ve been doing this however I seem to still get a countdown on the “second” cartridge.

Email me me so we can chat a little easier.

Th3designlab@gmail.com

Damien_Charles · 2017-02-11T16:52:16.000Z

Be careful CUBE3DFREE is a thief

he sells card that doesn’t work whith 3D printer Cube