Cubify Printers

namenotsekim · 2016-06-22T09:18:25.000Z

Hi Jerommeke

I have just joined the Hub, I also have a Cubepro and I am not happy.

I should have done more research prior to purchasing the thing…

Have you had any success with your rebuilding?

Regards

Mike

ROBERTOGEHLEN · 2016-07-19T17:53:34.000Z

Hack devices for all printers from Cubify, Cube, CubeX, CubePro … www.cube3dfree.com … worldwide products

Josh_Mcdorman · 2016-09-06T21:29:27.000Z

i agree this is a great printer but how do you solve the jamming in the nozzle my printer has been crippled with it and i end up wasting alot of filament

Josh_Mcdorman · 2016-09-06T21:30:25.000Z

love this printer but i keep getting jams in mid print does anyone have any suggestions?

Just3D · 2016-09-26T00:38:23.000Z

Hi Josh, don’t know if you got an answer to your question, but I just recently purchased a Cube 3 and with the limited amount of printing I’ve done I find the printer extremely reliable printing @ 200 microns. It does a really nice job at that setting too. I tried one part at 70 microns and after it printed the first layer or two it jammed. Today I pprinted a raspberry pi case both top and bottom on same print. It covered the whole print bed (thought I’d give it a challenge). Printed in ABS and outside of it curling up on one corner it printed fine (200 microns of course). It curled pretty bad but remarkably the case is still usable. I am pretty impressed with this printer especially since I bought it for $180. I will do some more experimenting at 70 micron to see if I can get it to print, but I recommend using 200 unless you have to have @70.

advancedrescue · 2016-10-29T01:41:11.000Z

Did you ever build the cube ultimaker?

SpencerR87 · 2016-12-14T13:33:38.000Z

I just bought mine Sunday. I’ve ran 25% of my filament already (2 cartridges) and haven’t had major issues. Definitely NO jamming on 200 or 70 microns. I’m having issues with gaps being left inbetween layers.

Just3D · 2016-12-14T14:56:24.000Z

Question - are you referring to gaps in height or on a specific layer? The reason I ask is because I have seen where the infill doesn’t come up to touch a feature. So say for instance I have a circle, the fill up to that circle doesn’t connect. I have yet to see any gaps in height from layer to layer. This is where pictures help to understand

SpencerR87 · 2016-12-14T15:04:46.000Z

It’s spaced in the layers I assume. (I’m a noob)

img_0197.jpg3024×4032 1.8 MB

Just3D · 2016-12-14T15:30:36.000Z

Have you checked your z gap? I have two of these printers and have learned not to trust auto. Every time I change a cartridge I rest it manually. Use the mylar strip that came with the printer. There should be slight drag nozzle when you slide the strip back and forth under it. I have yet to experience what I see in the pic and think z gap might be too high

SpencerR87 · 2016-12-14T16:09:09.000Z

Rick I have adjust and adjusted and adjusted the z-gap. This is a random occurring issue. It’s to the point I check the z-gap before every print. Since you have a few of these how do you add supports into it?

Just3D · 2016-12-14T16:29:15.000Z

I haven’t used support very much but when I have I just turned them on in the software. Does weird stuff as far as choosing where to put them. I’ve read about people using kisslicer to add support but I haven’t gone there yet. I am in the process of trying the filament hack to use standard filament rolls

SpencerR87 · 2016-12-14T16:29:46.000Z

Rick here’s a picture of that binky boat or what ever it is people like to print. My smoke stack is a little messed up.

img_0214.jpg3024×4032 1 MB

Just3D · 2016-12-14T16:51:36.000Z

Ha! That’s funny that you believe it is a flaw. I printed it and got the same thing and after close examination it looked to be an arrow. I asked family members what they though and they felt it could be. I went to the benchy website to see if that was a feature they mentioned and I couldn’t find it so maybe it is just messed up. I am at work right now but I post a pic of mine when I get home.

SpencerR87 · 2016-12-14T16:54:23.000Z

If you get it working (filament hack) please let me know what you did and how you did it.

Just3D · 2016-12-14T17:04:25.000Z

I’ll do that. I just found this on the kisslicer forum Cube (3rd Gen)??? - kisslicertalk.com

Just3D · 2016-12-15T21:48:24.000Z

Spencer, here is a pic of my benchy. Hard to show in red filament

img_20161215_164037183.jpg2592×1456 491 KB

ROBERTOGEHLEN · 2016-12-20T18:01:13.000Z

Now available chip reseter for CubePro and CubeX … no connections to printer required … www.cube3dfree.com

SpencerR87 · 2016-12-20T19:15:54.000Z

I use the cube 3

ROBERTOGEHLEN · 2016-12-20T19:39:16.000Z

Soon we will have a low cost solution for Cube 3 …