Ultimaker 2 - pros and cons?

[steven_10]

Yes you have to pay the Ultimaker tax, in that your 1st prints will be that of a new feed guide (bearing type) and new spooler (Also bearing type) and eventually a new extruder. but I have over 1000hrs on mine, printing PLA, ABS, Bronzefill, CopperFill, PLA/PHA (Colorfabb) and the only times it goes wrong is when I make a mistake slicing! they are one of the best printers out there! (I have been builing Repraps since Darwin came out so have a bit of experience…lol)

[fancyinterio]

we are using PLA has the raw material and not used any other material for printing apart from PLA, the printer is really good to buy and its prints at high resolution. it can be used mainly to build small sculpture and small engineering prototypes, For large architecture models the build plate is not enough. Now Ultimaker has provided extended model, but i feel that makerbot bed size is good for building large architecture models. I personally feel that the Bed size can be increased like Original Ultimaker that is older verson.

[DrieDeeDesign]

I am using my UM2 about 3 months now. For me as a newby, it is a realy good plug n play printer, probably the best you can get. Great quality prints, good support and a very large community and lots of info to find about it on the web. Con’s? Still no dual feed officially available and printing ABS is realy a hassle. But that is more a material problem with almost all printers. As others stated here already : buy good fillament!!! UM2 is still very custumizable and ready to tweak ur prints and experiment with it if you want in combination with Cura. I am one happy UM user and think you won’t regret buying one.

Good luck,

Frank

[Didier_2]

You should come on the forum to find solutions for your problems!

If you want to change the nozzle easily look for the olsson block (www.3dsolex.com)

[Flashp0int]

Yeah, I did some prints with Colorfabb woodfill fine printing 200+ micron layers fast.

But much higher risk of clogs and other challenges. Also except woodfill fine from Colorfabb all other resulted in clogs pretty much within the first 10-20 layers.

In comparison, my Rostock MAX with .6mm does not have that challenge. So not impossible, but would not recommend UM2 for this.

[danilius]

If you have never used a 3D printer before, then you are in for a shock, because 3D printing is really very, very hard beyond the simplest of things.

Having printed around 2000 hours on the Ultimaker 2, I find that it rarely fails on a print and can handle quite a broad variety of materials, including PLA, ABS, Nylon and NinjaFlex. But I suppose as is the case with every printer, if you want really great results the greatest skill you need is infinite patience and print things really slowly.

[Phil_CCR]

I’ve had one for 18 months and love it. The only negative is customer service which is amateurish at best (at worst, they simply ignore you until you kick a fuss). Having said that, there are lots of great people on the Ultimaker forum which somewhat compensates the poor service you receive from the manufacturer.

[Robin]

DISCLAIMER: I might be biased as I just got a job at Ultimaker (as of this month, I’ve had an Ultimaker 1 for almost 4 years )

pro:

- very good printer working out of the box.

- ease of use (if you can overlook printing via SD card, I’ve recently switched to SD card based printing(on my um original) and must say I don’t care much either way, until we have a printer that you can just send a file via the network it’s slightly inconvenient anyway)

- support open source development of the next better versions of cura, marlin and more.

- fast

- accurate (when not printing super fast) (has better x,y,z resolution than some other printers)

- reliable

- support, they can help people with problems etc.

- large and helpful user base

- upgrades, at least potentially (the ultimaker original got a whole bunch of upgrades)

con:

- the bowden tube makes it more difficult to print stuff like ninjaflex/fillaflex, as mentioned below it’s still possible though

- the feeder of the 2 is not as good as the current original (it is still light years ahead of the first version)

- price, it’s not the cheapest printer out there

there are printers that can beat it in say price (for example printrbot), or quality as some resin printers do, but resin is quite messy and far more toxic than PLA and often they don’t beat Ultimaker on multiple aspects imho.

[Pampentaucher]

I only can tell you about the Ultimaker Original. The Ultimaker does print the most filaments well. BUT the ULTIMAKER printer and the heated bed has the worst quality i’ve ever seen before. Much wrong parts, damaged parts, wrong connected cables, bad solderings and malfunktions. I have my Ultimaker since 9 month and its the third time that the printer is out of order. I’m very angry about the Ultimaker Company for that poor quality. Better by another Printer! Best Regards Pampetante

[Fabrice_Leger]

bonjour, ce là ne fais que deux mois que je la possède ,mais j’en suis très satisfais

je la trouve fiable ,je regrette juste qu’elle ne sois pas fermée pour certaine pièces

assez complexes que j’ai réalisé en ABS.

[AnnikavH]

What is Ultimaker prepaid card?

[gr5org]

Whatever you get, make sure it’s open source! I didn’t think that was important until after I got my printer. Can you imagine the manufacturer telling you that you can’t use other people’s filaments?

I have 3 UM2’s and a UMO. They are all great. Since you are a ME you should be fine with it. Get on the forums after you order it – tons of good stuff there.

It’s not like a 2D printer. It’s more like a CNC lathe or something on that complexity. But once you learn the issues with your particular typical parts that you print, by the 20th print you should be a pro and getting consistent successful results.

The biggest failing of the UM2 I believe is that at temps above 240C the teflon coupler wears out too fast (something like every 500 hours maybe?). I know people who print regularly at 290C but they have modded their printer with parts from 3dsolex.com So although it will print almost any material it is best at PLA by far. If you get the printer - bookmark these links:

A visual Ultimaker troubleshooting guide - 3DVerkstan Knowledge Base

Getting better prints - 3DVerkstan Knowledge Base

Designing for 3D printing - 3DVerkstan Knowledge Base

And no matter what you get, read the “designing for 3d printing” guide cover to cover (should only take an hour or so).

[novabeans]

Ultimaker Prepaid card :

Novabeans & Ultimaker to Offer Prepaid 3D Printing Cards Throughout...

[KCT]

I would advice the ultimaker 1 + @first i was happy with my 2 u2,s But they are having more problems So i.m a bit sorry igot them U1 + works exelent

[Sybren_Zwetsloo]

Hello Annika,

My recommendation would be to buy this printer. It is a very stable printer that gives good results. I have printed mainly with PLA, so can’t tell you much about the other mtaterials.

[insulaner]

Hi buy it ! It’s a funny experience.

[will_kostelecky]

I have an Ultimaker 2 and a Makerbot clone Wanhao Duplicator 4S. They are in two different classes from a price point which is a major con from the UM side. The beast is expensive! On the other hand you are getting quality for that money. The printer looks really nice, almost Apple’ish in terms of design.

The UM2 comes out of the box ready to print and do so at high quality. I was not particularly happy with some of the tuning options that Cura provides, in particular around bridging, but that is me being particular. I have moved to using Simplify3D and finally have a profile that I really like so I am happy with bridging!

Speaking of Simplify3D, and I am not marketing it just making a point, you normally should print from the SD card for reliability and even quality reasons, however, with Simplify3D you can print across the USB connection.

Whatever printer you get stay away from proprietary solutions. As someone else said…you need to be able to choose where you get your filament. I have cheap stuff that prints as well as expensive stuff. in that case you have to love the cheap stuff.

My one concern around the UM2 is whether you want to print ABS. IMHO the UM2 is really geared to printing PLA. No open printer is going to be as good at printing ABS as a closed printer. You can get stuff to close up the UM2 (even a bin liner can work) or you can keep it in a hot no draft closet, but if you should think about how much ABS you want to print before you buy the UM2.

Bottom line is that I would buy the UM2 again.

[will_kostelecky]

This is the truest of statements that I have ever read on a message board: “If you have never used a 3D printer before, then you are in for a shock, because 3D printing is really very, very hard beyond the simplest of things. …if you want really great results the greatest skill you need is infinite patience and print things really slowly.”

So very very true. It is lucky that I am retired because I have spent countless hours calibrating my two printers (UM2 and a Makertbot Clone) to be able to print a stupid calibration object (#3DBenchy). To the point of obsession. My wife would say beyond. But it is a beautiful thing when you see something go from your modeling software into reality and it is worth the pain.

[Bauermaker]

hi Annika

good choice, i have one Ultimaker 2 and 2 Ultimaker 1 and while i like the UM2, I still sometimes prefer the UM1 because everything is easier to fix and more hands on. The print quality is also pretty much the same, the single andvantage if the UM2 is that it has two fans, but you can easily add a second one to the UM1.

So if you are inclined to tinker a little bit i would recomend the Ultimaker 1+ (comes with a heated bed and the bed is a little bit “steadier” ) and you could also save some money

greetings

b

[3DBOX_3DBOX]

True, I have Ultimaker 2 and the heated bed always has probs.