Hello,
At PrintME 3D, we are resellers of Ultimaker 2 and are slightly biased!
Our thoughts on the Ultimaker 2 is that is produces excellent prints, simple to use and relatively stress free. Plus, the versatility on filaments is great, with brands like ColorFabb and NinjaFlex who test their products on the Ultimaker 2. Which basically means that you can use PLA, ABS, Nylon, Metal, Wood, Carbon and Rubber based filaments.
The only cons would be that like all 3D Printers, they do require maintenance. It is effectively a tool to heat and extrude plastic, so there will be on occasions issues with the hot end, but all of that is manageable.
They have also released the Ultimaker 2 Go and Ultimaker 2 Extended, effectively a smaller or larger version.
If you need any further help or want to order any products, feel free to email us at hello@printme3d.com
Thanks
PrintME 3D
Hi,
Ultimaker 2’s are great printers and it sounds like you have your mind made up to get one. It isn’t too loud and can print relatively quickly.
I’ve done some printing with flexible filament (Ninja Flex) as well as many types of PLA and ABS suppliers. It does jam up sometimes and will print in the air, so it’s always good to put a raft on your piece.
We have some on our website as well as options to purchase filament. https://robosavvy.com/store/3d-printing/filter/manufacturer/ultimaker.html
Let me know if you have any more questions, and enjoy printing!
Joe
Robosavvy
Well, i think the UM2 will be perfect for you.
It’s reliable and has a really good price/quality ratio. The Cura software is really intuitive and yet, very complete.
The minimum resolution is 0.06mm, well below 0.2mm.
I use the UM2 in the same context as you described and it works perfectly. If you have any questions or problems operating the machine, the official forum is always here to help you.
Cleven
June 24, 2015, 1:36pm
20
The only issue is the feeder system *though it does work, issues are only witnessed at higher speeds*. There have been some slight improvements to the PTFE coupler inside which has improved things greatly. There are also versions that can be printed which work very well.
Note that the PTFE and the bowden tube will eventually wear if you do a lot of printing. I suggest ordering extra if you are planning to do a lot of printing.
Hey There. This is the only printer I have ever used so I can’t really compare it. But I will say if you are trying to print any materials other than PLA, PET, or ABS… Then don’t waste the money. It is a great printer but it’s even hard to get ABS to print… At least for me but I’ve only tried one spool so it may be the material I bought. ABS just doesn’t want to stick to the hotbed. Other cons would be changing the nozzle, there should be an easier way than taking the whole print head apart, and you only have one nozzle size option. Also if you remove the glass to get your part off you’ll have to level the bed again once you go to print again. Once again I have zero experience with any other printer so I can’t really compare it to much but it does print PLA like a Champ! lol kinda bummed that I can’t get any other materials to print that well. Don’t want to stray you away from the machine cause it is solid but I think the biggest downfall is the material options, for me at least.
Yes you have to pay the Ultimaker tax, in that your 1st prints will be that of a new feed guide (bearing type) and new spooler (Also bearing type) and eventually a new extruder. but I have over 1000hrs on mine, printing PLA, ABS, Bronzefill, CopperFill, PLA/PHA (Colorfabb) and the only times it goes wrong is when I make a mistake slicing! they are one of the best printers out there! (I have been builing Repraps since Darwin came out so have a bit of experience…lol)
1 Like
we are using PLA has the raw material and not used any other material for printing apart from PLA, the printer is really good to buy and its prints at high resolution. it can be used mainly to build small sculpture and small engineering prototypes, For large architecture models the build plate is not enough. Now Ultimaker has provided extended model, but i feel that makerbot bed size is good for building large architecture models. I personally feel that the Bed size can be increased like Original Ultimaker that is older verson.
I am using my UM2 about 3 months now. For me as a newby, it is a realy good plug n play printer, probably the best you can get. Great quality prints, good support and a very large community and lots of info to find about it on the web. Con’s? Still no dual feed officially available and printing ABS is realy a hassle. But that is more a material problem with almost all printers. As others stated here already : buy good fillament!!! UM2 is still very custumizable and ready to tweak ur prints and experiment with it if you want in combination with Cura. I am one happy UM user and think you won’t regret buying one.
Good luck,
Frank
You should come on the forum to find solutions for your problems!
If you want to change the nozzle easily look for the olsson block (www.3dsolex.com )
2 Likes
Yeah, I did some prints with Colorfabb woodfill fine printing 200+ micron layers fast.
But much higher risk of clogs and other challenges. Also except woodfill fine from Colorfabb all other resulted in clogs pretty much within the first 10-20 layers.
In comparison, my Rostock MAX with .6mm does not have that challenge. So not impossible, but would not recommend UM2 for this.
If you have never used a 3D printer before, then you are in for a shock, because 3D printing is really very, very hard beyond the simplest of things.
Having printed around 2000 hours on the Ultimaker 2, I find that it rarely fails on a print and can handle quite a broad variety of materials, including PLA, ABS, Nylon and NinjaFlex. But I suppose as is the case with every printer, if you want really great results the greatest skill you need is infinite patience and print things really slowly.
8 Likes
I’ve had one for 18 months and love it. The only negative is customer service which is amateurish at best (at worst, they simply ignore you until you kick a fuss). Having said that, there are lots of great people on the Ultimaker forum which somewhat compensates the poor service you receive from the manufacturer.
Robin
June 24, 2015, 1:56pm
29
DISCLAIMER: I might be biased as I just got a job at Ultimaker (as of this month, I’ve had an Ultimaker 1 for almost 4 years )
pro:
- very good printer working out of the box.
- ease of use (if you can overlook printing via SD card, I’ve recently switched to SD card based printing(on my um original) and must say I don’t care much either way, until we have a printer that you can just send a file via the network it’s slightly inconvenient anyway)
- support open source development of the next better versions of cura, marlin and more.
- fast
- accurate (when not printing super fast) (has better x,y,z resolution than some other printers)
- reliable
- support, they can help people with problems etc.
- large and helpful user base
- upgrades, at least potentially (the ultimaker original got a whole bunch of upgrades)
con:
- the bowden tube makes it more difficult to print stuff like ninjaflex/fillaflex, as mentioned below it’s still possible though
- the feeder of the 2 is not as good as the current original (it is still light years ahead of the first version)
- price, it’s not the cheapest printer out there
there are printers that can beat it in say price (for example printrbot), or quality as some resin printers do, but resin is quite messy and far more toxic than PLA and often they don’t beat Ultimaker on multiple aspects imho.
2 Likes
I only can tell you about the Ultimaker Original. The Ultimaker does print the most filaments well. BUT the ULTIMAKER printer and the heated bed has the worst quality i’ve ever seen before. Much wrong parts, damaged parts, wrong connected cables, bad solderings and malfunktions. I have my Ultimaker since 9 month and its the third time that the printer is out of order. I’m very angry about the Ultimaker Company for that poor quality. Better by another Printer! Best Regards Pampetante
bonjour, ce là ne fais que deux mois que je la possède ,mais j’en suis très satisfais
je la trouve fiable ,je regrette juste qu’elle ne sois pas fermée pour certaine pièces
assez complexes que j’ai réalisé en ABS.
What is Ultimaker prepaid card?
gr5org
June 24, 2015, 2:55pm
33
Whatever you get, make sure it’s open source! I didn’t think that was important until after I got my printer. Can you imagine the manufacturer telling you that you can’t use other people’s filaments?
I have 3 UM2’s and a UMO. They are all great. Since you are a ME you should be fine with it. Get on the forums after you order it – tons of good stuff there.
It’s not like a 2D printer. It’s more like a CNC lathe or something on that complexity. But once you learn the issues with your particular typical parts that you print, by the 20th print you should be a pro and getting consistent successful results.
The biggest failing of the UM2 I believe is that at temps above 240C the teflon coupler wears out too fast (something like every 500 hours maybe?). I know people who print regularly at 290C but they have modded their printer with parts from 3dsolex.com So although it will print almost any material it is best at PLA by far. If you get the printer - bookmark these links:
And no matter what you get, read the “designing for 3d printing” guide cover to cover (should only take an hour or so).
3 Likes
KCT
June 24, 2015, 3:16pm
35
I would advice the ultimaker 1 + @first i was happy with my 2 u2,s But they are having more problems So i.m a bit sorry igot them U1 + works exelent
Hello Annika,
My recommendation would be to buy this printer. It is a very stable printer that gives good results. I have printed mainly with PLA, so can’t tell you much about the other mtaterials.
