Perry I don’t mean to be rude, but being bluntly honest I think you’re beating a dead horse here. You’ve starting coming across somewhat hostile and I honestly don’t think it’s doing anything to strengthen your point other than obfuscating this chat to the point that it’s hard to have actual discussions on what can be done about the matter. If I had any advice it would be to just step back and take a breath for a second. I understand you are frustrated, but repeating the same thing over and over is in reality accomplishing nothing. That being said this extends out to everyone on these forums, they’re meant for collaboration. I just think you should lay back on your comments towards @filemon and @3DHubs and give them some time to react. It’s not something that can be impulsively done, they have to consider all the options, if it’s worth their time, then troubleshoot solutions, fease them out, get them approved, and then implement.
Perry I don’t mean to be rude, but being bluntly honest I think you’re beating a dead horse here. You’ve starting coming across somewhat hostile and I honestly don’t think it’s doing anything to strengthen your point other than obfuscating this chat to the point that it’s hard to have actual discussions on what can be done about the matter. If I had any advice it would be to just step back and take a breath for a second. I understand you are frustrated, but repeating the same thing over and over is in reality accomplishing nothing. That being said this extends out to everyone on these forums, they’re meant for collaboration. I just think you should lay back on your comments towards @filemon and @3DHubs and give them some time to react. It’s not something that can be impulsively done, they have to consider all the options, if it’s worth their time, then troubleshoot solutions, fease them out, get them approved, and then implement.
1 Like
@PepCo_Parker Thank you for not being rude and being bluntly honest, while offering your opinion. I am doing the same, and have the right to do so.
I would like to point out I was answering a specific question that was directed specifically to me. I was not beating a dead horse, but was answering a specific request for an opinion.
@filemon is a big boy. He can take it, so can I. He even said to continue the discussion here on the phone call, if you recall.
As for repeating myself, that is a legitimate form of protest on a forum when responses are sparse. Collaboration requires response.
I have no intention of stepping back. Do you recommend the same for @Steelmans whose question I was answering? And other hubs that show lost business in this thread? Do you suggest they step back for several months?
You state going back to the other wording is something that can not be impulsively done. I must disagree, they can change back from the at any time, otherwise it would be a pretty poor test.
Silence will get us nowhere. Sorry. The last time this type of change was made, it floated into thread history pretty rapidly, and was simply ignored. I am just trying to keep this from happening again.
I have been exceedingly civil, but sometimes facts and opinions can be difficult to read, particularly when you are questioning someones motives, as I have done here. My goal is still honorable, to protect our market, and to prevent 3dhubs from making what I consider to be a very big mistake. My motivations are clean.
BTW, hostile is inaccurate. Angry is accurate.
2 Likes
I’m not saying to step back*and do nothing*, but I do know if this was a group of people collaborating, one person constantly bringing up the same points without taking a break quickly tires and frustrates others. In this situation, the issue ends up being people have to scroll for several minutes to sift through all the repetition to get to the progress. You are right that you were answering a specific question, but the answer was essentially just a repeat of your other post and summaries. This is a very active forum, and it’s great to see collaboration, but I do believe there comes a point where it is in excess and is not benefiting the cause in a positive manor. That being said, I am no god, I am not 100% right 100% of the time, and this is just my opinion. At the same time, I know it is now almost impossible for me to follow this thread and get any meaningful information from it, as well, my email is filled with notifications that I have to sift through as I didn’t unsubscribe from the forum in time.
1 Like
I would add that ABS as prototyping plastic is silly, many final objects are ABS, including the mouse I am using, I would think.
Also, it is wrong and confusing because the other cards have not changed. So prototyping as a result shows in several of the other cards. Its just bad wording. I agree, a test to see if no fewer FDM orders is what is being measured, they are in fact testing something that is just wrong. If the data shows FDM orders went up, it would no less wrong.
“I can’t seem to get over this” Don’t get over it. Stay vocal.
@PepCo_Parker
I have much respect for you, your input, and your continued help with others here in “Talk” who need help from experienced hubs. You are great!
And you and I, in general, do not disagree on the many of the issues here, so disagreeing on the effectiveness of repeating points, particularly in response to new posts is not so bad. I do have a tinge of protest in my motivations, as well.
Also, I think you were off the thread for awhile, if I recall, so reading it from top to bottom, instead of how it occurred naturally over two weeks, it certainly reads much worse! Plus, if we do not respond, the thread will disappear, something we should not be willing to let happen, at the cost of it being unwieldy.
After this is all over, I hope you resubscribe. The forum really does need folks like you.
Yeah for sure! Thanks BTW Perry. You’re right about me being away for a few days. I turned off my notifications for it and then didn’t get back into the conversation until a few days later. That definitely made it much harder to follow the thread!
For even more fun, pretend you are the customer placing an order and you want to select BronzeFill or WoodFill…
Oh, buy you don’t know that is what it is called, no cheating with search terms.
Good Luck!
1 Like
Update #1:
Hi all, the ‘material disclaimer’ on FDM has been removed for the reasons discussed in this thread. To give full disclosure, we might still add such material disclaimers in the future but we’ll do that on another note and across all materials when we do, not just FDM. More updates later.
2 Likes
@Filemon A good start! 
By the way, thanks for the meeting yesterday. My new customer orders have picked up already.
1 Like
I have a really random question for you Filemon, at first I thought the 20XX printer guide badges just get removed each year but after seeing everyone else’s I realized this wasn’t the case. I had the 2016 printer guide badge (as I contributed to it) until the newer one came out for 2017. After that I had the 2017 one but the 2016 disappeared… is there any reason why or information about how I can get it back? Thanks in advance 
Hi @PepCo_Parker, the support guys should be able to help you with that. Just shoot them an email and they’ll get your badge back up
1 Like
Hi Simon, you were right on this one. Got it fixed. Thanks again!
2 Likes
Thanks filemon. Once I realized I figured it had just been a glitch but I wanted to make sure!
Another positive move. Keep going, you’re on a roll!
@Filemon Thanks for removing that. That takes care of my #2 issue, of customers seeing that when they were repeat customers to my hub.
Hey Filemon,
I’m usually not a grammar nitpicker (at least not to other people!), but the change you made on the Accept or Decline page (see the attached jpeg) - shouldn’t it read “or the customer and I have agreed…” rather than “or me and the customer have agreed…”
Mark
