Possibly Bricked Qidi Tech printer when installing sailfish?

RCONSTRUCT · 2016-06-11T15:36:21.000Z

Where do you get AVRDUDE?

RCONSTRUCT · 2016-06-11T18:02:53.000Z

Could you link the tools I need to do this?

RCONSTRUCT · 2016-06-14T20:11:29.000Z

Hi again Ryuluce. I have accidentally screwed up my printer by trying to reset the board after having a stepper motor failure. I now have the AVR programmer but am unsure on how to use it. Do you happen to know the orientation of the pins on the motherboard? I’d hate to put power to ground.

Ryuluce · 2016-06-14T21:45:46.000Z

Okay, so you’ll notice that the ICSP pins for the ATMEGA1280 have a white dot near one corner, right? That white dot represents the upper-right of the standard ICSP pin configuration.

You’ll also notice that the programmer plug has a notch on one of the long sides, that represents the top of the ICSP pin configuration.

So, the notch on the programmer plug should be on the same long side as the white dot.

In other words, the white dot points out pin one.

RCONSTRUCT · 2016-06-14T22:12:31.000Z

Unfortunately I don’t have either of those. I have uploaded a photo.

Do you k now where I can get AVR studio 4?

IMG_4859[1].JPG3024×3024 1.53 MB

RCONSTRUCT · 2016-06-14T22:48:36.000Z

Okay, I have AVR studio 4 but am failing to connect.

Ryuluce · 2016-06-14T23:32:25.000Z

The programmer appears plugged in correctly to me.

As for the AVR studio 4, I’m afraid you’re on your own on that front. I’ve used only AVRDUDE and ATMEL Studio.

Ryuluce · 2016-06-14T23:32:55.000Z

I can’t help on that front, I’ve never worked with AVR Studio.

RCONSTRUCT · 2016-06-15T00:02:43.000Z

Ah no problem. I’m going to use AVRDUDE. I have some help from another person who went through it and gave me the hex files. I guess what I need to know now is how to use AVRDUDE such as making sure the connector I bought even works. I’ll come back and update.

RCONSTRUCT · 2016-06-23T00:44:30.000Z

Hi there and thanks again for replying. I have an programmer now and am familiar with avrdude. Do you have the commands I need to flash to the motherboard in order to get this working?

Right now I’m using:

avrdude -p m1280 -F -P usb -c usbasp -U flash:w:/Makerbot-usbserial.hex \ -U lfuse:w:0xFF:m -U hfuse:w:0xDA:m -U efuse:w:0xF4:m -U lock:w:0x0F:m

and

avrdude -p m1280 -F -P usb -c usbasp -U flash:w:/atmega1280.hex \ -U lfuse:w:0xFF:m -U hfuse:w:0xDA:m -U efuse:w:0xF4:m -U lock:w:0x0F:m

to the 8u2 ICSP port but to no avail. Avrdude says it completed but had a verification error. Also I see no com6 in repG

Ryuluce · 2016-06-23T01:01:32.000Z

Okay, to make troubleshooting easier, could you try again with a verbose output and funnel the command’s output to a text document?

To do that, use this command:

avrdude -v -v -v -p m1280 -F -P usb -c usbasp -U flash:w:/Makerbot-usbserial.hex \ -U lfuse:w:0xFF:m -U hfuse:w:0xDA:m -U efuse:w:0xF4:m -U lock:w:0x0F:m > Troubleshoot.txt

That should output all the command’s response into a .txt file that can be used for troubleshooting.

RCONSTRUCT · 2016-06-23T03:06:15.000Z

Will do. Just so I’m clear. I was flashing the atmega1280.hex to the 1280 header and the usbserial.hex to the 8u2 ICSP. Is this correct?

RCONSTRUCT · 2016-06-23T03:07:34.000Z

avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as F4
avrdude: safemode: lfuse reads as FF
avrdude: safemode: hfuse reads as D9
avrdude: safemode: efuse reads as F4

Ryuluce · 2016-06-23T04:18:25.000Z

Wait, the 8u2 chip on the motherboard…? You’re talking about the separate chip on the motherboard?

You… shouldn’t have touched that…

That chip has nothing to do with the firmware flashing, it’s all in the ATMEGA1280 chip.

The fuses you need to adjust are in that chip too as far as I’m aware.

That firmware does NOT belong in the atmega8u2 chip, that’s something else entirely…

I really, really hope you backed up the flash and fuse settings for that chip, or at least can find them online.

If not, you really did brick your printer if it isn’t starting up right now.

That chip at least doesn’t use the “-p m1280” setting in AVRDUDE, so maybe you didn’t break it…

EDIT: for fixing the atmega8u2, this link has some info:

https://groups.google.com/forum/m/?fromgroups#!topic/makerbot/-S01iIYO2E8

RCONSTRUCT · 2016-06-23T18:16:41.000Z

Okay, okay. Still so confused and someone else had posted on here with what I believe was incorrect information.

There is the 1280 ICSP port. The 1280.hex goes on that, correct?

The command would be: avrdude -p m1280 -F -P usb -c usbasp -U flash:w:/Makerbot-usbserial.hex \ -U lfuse:w:0xFF:m -U hfuse:w:0xDA:m -U efuse:w:0xF4:m -U lock:w:0x0F:m

There is an 8u2 ICSP port. The makerbot usb hex goes on that, also correct?

The command would be: avrdude -p at90usb82 -F -P usb -c usbasp -U flash:w:Makerbot-usbserial.hex -U lfuse:w:0xFF:m -U hfuse:w:0xD9:m -U efuse:w:0xF4:m -U lock:w:0x0F:m

You had mentioned flashing the firmware directly and avoiding repG altogether. I can do that to the 1280 ICSP port, right?

Ryuluce · 2016-06-23T18:48:36.000Z

If you look in this thread, I have a post giving simple instructions on uploading the firmware.

To be brief, flash the firmware (with the fuse settings) to the 1280 icsp port.

The 8u2 does control the usb, but you really shouldn’t have messed with that in the first place, the flash memory that was already on it was fine.

That response I gave you yesterday linking to that thread should have the information regarding reseting the 8u2’s flash memory back to defaults.

RCONSTRUCT · 2016-06-23T18:59:20.000Z

Thanks so much. I was in a bind so I was taking advice from the wrong people. I will give it a shot tonight. Thanks again.

RCONSTRUCT · 2016-06-23T22:02:44.000Z

avrdude is not recognizing at90usb82

Ryuluce · 2016-06-23T23:07:23.000Z

Hm, try some of these links:

http://avr.2057.n7.nabble.com/Config-AVRDUDE-for-ATmega8U2-td18846.html

http://www.avrfreaks.net/forum/avrdude-and-atmega8u2

https://forums.adafruit.com/viewtopic.php?f=24&t=19357

http://www.matbra.com/en/2012/11/02/programando-atmega8u2-no-arduino-uno-utilizando-usb-asp/

RCONSTRUCT · 2016-06-23T23:38:04.000Z

FIXED! Okay I didn’t bother with the 8u2 and I don’t think it ever got messed up. I ended up having to install WinAVR and reran the same commands. I think I had too old of a version of AVRDUDE? Anyway, I had a blank screen still and same problem after reflashing the Atmega1280.hex to the 1280 port but after then flashing Sailfish 7.1 hex for a Replicator 1 Dual it started beeping!

Now my issue is that when I home axes the X axis buzzes like crazy like it is going to tear the printer apart. I noticed the back left stop switch red light isn’t coming on, is that the problem?